Quick Service Guide 340a

Discount Flats

Standard Mail Nonautomation Flats

May 2007
Printer-Friendly PDF

Related QSG

703, Standard Mail Nonprofit Eligibility

Physical Standards (301)

Maximum weight: less than 16 ounces.

For an overview of the physical standards for discount flats, see Quick Service Guide 301.

Rates and Fees (343.1.0)

Destination discounts apply to mail prepared as prescribed by USPS and addressed for delivery within service area of destination BMC/ASF or SCF (346.2.0).

Annual $175.00 presort mailing fee.

Content (343.2.0)

Flats containing mailable items not required to be sent using First-Class Mail can be sent using Standard Mail. Standard Mail is typically used for advertisements, flyers, and catalogs. Additional content restrictions must be met for authorized nonprofit mailers (703.1.0).

Eligibility Standards (343.3.0)

Mailings of 200 or more addressed pieces (or 50 pounds of addressed pieces), sorted and marked as described below. All pieces must meet the physical standards for flats (301). Pieces are eligible if not required to be mailed at First-Class Mail rates or not eligible for Periodicals rates. Nonprofit rates require specific authorization (703.1.0).

Each piece must include a complete delivery address with correct ZIP Code or ZIP+4 code.

A certified process (233.3.6.2) must be used within 12 months before mailing to ensure accuracy of 5-digit ZIP Codes.

Rigid, nonrectangular, and pieces that are not uniformly thick must be prepared as parcels or Not Flat-Machinable pieces and pay parcel or Not Flat-Machinable rates (343.3.2.1).

Mailers can apply Repositionable Notes for an additional charge of $0.015. See 709.5.0.

Postage Payment and Documentation (344)

Precanceled stamp (604.3.0), meter (604.4.0), or permit imprint (604.5.0).

Additional standards apply to mailings of nonidentical-weight pieces.

Documentation:

Mail Preparation (345)

Marking on each piece in the postage area (302.2.0):

See reverse for preparation and labeling.

Palletization is preferred, see Quick Service Guide 705d.

Any mailing job that contains bundles of Presorted flats and bundles of automation flats must be co-sacked using 705.9.3.

Enter and Deposit (346)

Mailing entered at an acceptance point designated by USPS.

For the specific DMM standards applicable to this category of mail, consult the DMM sections referenced above and the general sections within each DMM module.

Bundling and Sacking Sequence (345.5.0)
5-Digit/Scheme1 Bundles: Scheme bundles required for 5-digit ZIP Codes in L007. Required with 15 pieces for mailings containing only pieces weighing 5 ounces or less. Required with 10 pieces for mailings containing any pieces weighing more than 5 ounces. Fewer pieces in a bundle not permitted. Labels: Red Label 5 or optional endorsement line (OEL).	3-Digit/Scheme1 Bundles: Scheme bundles required for 3-digit ZIP Codes in L008. Required with 10 or more pieces to same 3-digit/scheme; fewer than 10 pieces in a bundle not permitted. Labels: Green Label 3 or OEL.	ADC Bundles: Required with 10 or more pieces to same ADC (see L004); fewer than 10 pieces in a bundle not permitted. Labels: Pink Label A or OEL.	Mixed ADC Bundles: Any remaining pieces must be bundled in mixed ADC bundles. Labels: Tan Label X or OEL.
5-Digit/Scheme2 Sacks: Required when there are 125 pieces or 15 pounds to the same 5-digit/scheme; smaller volume not permitted.3 Labels: Line 1: For 5-digit scheme sacks, use L007, Column B. For 5-digit sacks, use city, state, and 5-digit ZIP Code on mail. Line 2: For 5-digit scheme sacks, use "STD FLT 5D SCH NON BC." For 5-digit sacks, use "STD FLTS 5D NON BC." Rate: 5-Digit	3-Digit Sacks: Required when there are 125 pieces or 15 pounds; smaller volume not permitted. Optional: After all full sacks are prepared, mailers may make one less-than-full sack for any remaining bundles for each origin 3-digit ZIP Code prefix of SCF serving post office where mail is verified. Labels: For Line 1, use L002, Column A, for destination facility. Rate: 3-Digit or ADC4	ADC Sacks: Required when there are 125 pieces or 15 pounds; smaller volume not permitted. Labels: For Line 1, use L004, Column B for destination facility. Rate: ADC	Mixed ADC Sacks: Any remaining bundles placed in mixed ADC sacks. Labels: For Line 1, use L009, Column B. Rate: Mixed ADC
Rates are based on sack level.

1Pieces meeting the automation-compatibility standards in 301.3.0 must be prepared in 5-digit scheme and 3-digit scheme bundles. Mailers must prepare all possible 5-digit scheme bundles and 5-digit scheme sacks before preparing 5-digit bundles and 5-digit sacks. All possible 3-digit scheme bundles must be prepared before preparing 3-digit bundles and 3-digit sacks. 2For 5-digit scheme sacks, use "STD FLT 5D SCH NON BC," for 5-digit sacks, use "STD FLTS 5D NON BC." 3 For nonidentical-weight pieces, see 345.5.5b. 4ADC rate for any 3-digit sack for origin SCF not meeting 125-piece or 15-pound minimum.

Back to Top